Date published 

 

each, the 16K requires an bit data word address for random word addressing. WP Pin. Status. Part of the Array Protected. 24C01A. 24C 24C 24C08A. Part Number: 24C02N Function: 2-wire serial EEPROM / AT24C01A/02/04/08A/ 16A Series Maker: Atmel Corporation Pinouts: 24C02N. 24C02/24C Two-Wire Serial EEPROM. Preliminary datasheet. 2K ( X 8)/ 4K ( X 8). 1/ MRD. Features. ▫. Low-voltage and Standard-voltage.

Author:NGAN BUGLISI
Language:English, Spanish, German
Country:South Africa
Genre:Fiction & Literature
Pages:743
Published (Last):25.01.2016
ISBN:212-6-23341-350-9
Distribution:Free* [*Registration needed]
Uploaded by: SALLEY

59331 downloads 90472 Views 22.44MB ePub Size Report


24c02n Datasheet Ebook

24C01 - 1Kbits ( bytes); 24C02 - 2Kbits ( bytes); 24C04 - 4Kbits datasheet of that EEPROM and look into first page under "Features". But I have used 24C04 instead of 24C02 & it is working alright. So my question is that Did you ever look into the data sheets? The answer. Now the problem is: as I go through the datasheets of all such I2C serial memories there is a memory reset in that of AT24C02 which is not.

Malamuro The product does not contain any of the restricted substances in concentrations and applications banned by the Directive, and for components, the bsp75n is capable of being worked on at the higher temperatures required by lead—free soldering. You can change your bsp75n settings by reading our cookie policy. Diagnosis or bsl75n and bsp75n protection Easy drop in replacements. The Manufacturers reserve the bsp75n to change this Information at any time without notice. Image representative of range only. Bsp75n to parts bsp75n Save to parts list. You can view the embedded page here. Infineon welcomes your comments and questions. Our website uses cookies and similar technologies to provide you with a bsp75n service while searching or placing an order, for bsp75n purposes and to personalise our advertising to you. Your bsp75n will be sent to the appropriate bsp75n who will be in touch with you as soon as possible. Find an answer to your question Unfortunately, your browser does not support bsp75n frames iframes: Attribute Value Configuration Single 1: I have read the privacy policy and agree with it. You will bsp75n a confirmation E-mail to validate your address in our system. RS Components Statement of conformity. Save bsp75n item to a new parts list.

If you have other questions about this product contact us here.

Поддерживаемые чипы

Table of contents The external power supply should be connected to the VIN terminal, with the voltage between 2. Smart Buck click provides two independent output voltage channels, each with the ability to output a regulated voltage in the range between 0.

It is able to provide up to mA for the connected load at each of the output terminals. With the ability to programmatically set both voltage values independently while providing reasonably high current, offering 2kbit of non-volatile memory and voltage and current monitoring for both outputs and two input voltage points, Smart Buck is a perfect solution for many different applications, especially well suited for the embedded and IoT applications.

How does it work? The dual buck converter works in synchronous PWM mode, whenever the load drains more than mA. The operating mode of the converter is switched to so-called Trickle mode when the connected load drains less than mA.

Smart Buck click

Although highly efficient for the light loads, this mode has its downsides, such as the slightly increased ripple and increased voltage regulation tolerance. For most cases when the supplied device enters the standby mode, when the system is suspended, and similar this is sufficient, but for some critical low current applications, the MIC can be set to always operate in synchronous PWM mode at 2.

This IC is a dual 8-bit digital potentiometer with the non-volatile memory and the WiperLock function, from Microchip. The internal digital potentiometers are connected as the rheostats, acting as the second, variable resistor of the feedback voltage dividers.

Code for EEPROM 24C02 through 24C

This allows setting the output voltage, by programming the digital potentiometer values via the I2C interface. For the power monitoring purposes, Smart Buck click uses the PAC , a four-channel DC power and energy monitor with the accumulator, from Microchip.

The operating mode of the converter is switched to so-called Trickle mode when the connected load drains less than mA. Although highly efficient for the light loads, this mode has its downsides, such as the slightly increased ripple and increased voltage regulation tolerance.

For most cases when the supplied device enters the standby mode, when the system is suspended, and similar this is sufficient, but for some critical low current applications, the MIC can be set to always operate in synchronous PWM mode at 2.

This IC is a dual 8-bit digital potentiometer with the non-volatile memory and the WiperLock function, from Microchip.

Smart Buck click

The internal digital potentiometers are connected as the rheostats, acting as the second, variable resistor of the feedback voltage dividers. This allows setting the output voltage, by programming the digital potentiometer values via the I2C interface. For the power monitoring purposes, Smart Buck click uses the PAC , a four-channel DC power and energy monitor with the accumulator, from Microchip. This IC also contains a high-performance digital section, accessible via the I2C interface, which is used to integrate the measurement results and provide on-chip power calculations, reducing the processing load of the MCU.

Single Shot and Continous modes are at disposal, allowing fine-tuning of its functionality. It has four channels of which two are used to monitor current and voltage on the two output terminals.

The sensing elements which are connected to the PAC are low-value resistors, ranging from 0. The channel inputs are differential pairs, which are implemented as the Kelvin connection to sensing resistors. Kelvin connection allows very precise measurements, since the voltage drop along the sensor traces due to their resistance, is eliminated. Switching it to 1 will enable the slow sampling feature of the PAC, enforcing the sample rate of 8sps, regardless of the CTRL register content.